Tag Archives: carbon

Emeralds

Emeralds are a green crystal of beryllium-aluminum silicate. The chemical formula is Be3Al2(SiO3). They are hexagonal prismatic crystal with a hardness of 7 1/2 to 8 on the Mohs scale. They are not tough stones and may be broken easily by mishandling or the use of severe chemicals or ultrasonic cleaners. If you own an emerald, be careful of it. Don’t wear it during sports. Don’t have a jeweler clean it in an ultrasonic cleaner as it may shatter.

Emeralds also break under applications of heat and should never be in a ring that is soldered. Under ultraviolet light they may fluoresceslightly, orangish red to red, or they may be inert.

Emeralds come from a number of sources. The best come from Colombia. These are the purest colored and generally the finest stones. The emeralds from Brazil are lighter, have more inclusions and are generally smaller than from other areas. Zambia, Africa, produces some bluish stones and some near-Colombian stones. Zimbabwe is home to a particular emerald known as the sandawana emerald which is generally small with a rich green color. Anything over 1/3 carat is rare.

South Africa produces some low-quality emeralds. Tanzania produces a few very good quality emeralds. Pakistan has just discovered some high-quality emeralds. Afghanistan tends to produce flawed but good colored emeralds. USSR does produce emeralds but doesn’t like to let them out of the country. Australia produces some dubious quality emeralds and North Carolina a few gems. Austria and India occasionally produce emeralds.

Emeralds are not unusual as the word emerald simply indicates an extremely nice version of a fairly common stone known as beryl. It is possible to buy something legitimately called an emerald for about $5 a carat. Obviously this is full of flaws, not transparent and so impure in color it looks more like jade than an emerald. They would never be sold in a jewelry store but emeralds do sell on TV and some of the better magazines for $5 per carat.

Gem quality emeralds range anywhere from $400 to $18,000 a carat, depending upon their quality. As the stones get larger, they become increasingly rare and sell for considerably more money.

Color is a critical factor in emeralds and constitutes about half of the stone’s value (clarity 30% and cut 20%).

Hue describes the primary color and any other colors in the stone. Most emeralds are green hued with a bluish hue also visible, especially the better Colombian-type emeralds.

Tone is the depth or darkness of the color as perceived by the eye.

Saturation is the amount of hue present in any given color.

Depending upon where the emeralds come from, they can exhibit a wide range of color; i.e., Brazilian emeralds are usually lighter toned and less saturated than their Colombian cousins.

The green in the emerald is caused by trace elements of chromium and/or bandium. If the color is very light green, the stone is more correctly referred to as green beryl, not emerald.

Emeralds are often oiled to help their appearance. Normally an uncolored oil such as Merck cedarwood oil is used. The stone may soak in the oil for several days and will actually take the oil in somewhat, helping bring out the color and “wedding” on some of the dry inclusions, making the stone look better.

If one finds an emerald that is mild in color or has a grayish hue, it is a good bet to soak it in oil a couple days and it may regain its green color, not to mention its value.

A more unscrupulous “improvement” is to use dye or oil with color in it. It is possible to influence the color of a stone by having it soak up colored oil.

Other problems with buying emeralds are the fact that there are a number of stones that look like emeralds and overlap colors. Tsavorite, a garnet found in Kenya and Tanzania, looks quite a bit like emerald and has a pure green hue, although it tends to be a little bit more yellowish and never has the blue hue of emerald.

Chrome tourmaline is another stone that looks much like an emerald with a moderately strong green color. Another emerald look-alike comes from Africa and is called chrome diopside. All these stones can, and are, sold as emeralds to the unwary.

Different emeralds from different areas tend to have individually shaped inclusions; i.e., slight pyrite inclusions are typical of emeralds from Colombia although they can be seen in stones from other sources.

A three phase inclusion that shows up under a 1 Ox or stronger microscope, which has a distinctly liquid area, a gas bubble in a solid square rock crystal, salt Iying superimposed on each other inside a jagged edged cavity, is typical of emeralds from Colombia and proves their natural origin.

Tropiche emeralds from Colombia sometime exhibit six fine radiating arms of black carbon inclusions, spoke-like in appearance. Another type of this stone has six arms of emeralds extending from the center of the crystal with a white shaped wedge area in between. When these stones are cut and mounted, they are valuable because of their inclusions.

Emeralds are subject to not only customs duty but market restraints as there is no OSO type organization supporting them. It is possible, if one is smart and has verification equipment, to buy emeralds in other countries, notably South America, and smuggle them to America for profit. Coincidentally, the areas one smuggles emeralds from are the same areas one smuggles cocaine from and these passport stamps tend to yell search me, search me. Some people even go to the trouble of swallowing and then recovering emeralds although obviously, we do not encourage or advise this dangerous practice.

Clarity of diamonds

The first C is clarity. This is not the most important but is generally the
first item looked at in a stone to be rated. Clarity does not refer to the
concept of “being clear” with reference to a diamond. Clarity refers to the
purity of the stone and lack of visible defects.
These defects or flaws or as they are properly known, inclusions, may manifest
themselves as dark, black carbon spots, white carbon spots, small cracks,
“clouds”, feathers, or other areas of visible diffusion within a diamond or on
the surface of the stone itself.
A truly flawless stone, one without any spots, cracks or inclusions, is very
rare and extremely valuable. One can expect to find some flaws in most stones.
The type of flaws, size of flaws, and location will have an effect upon the
stone’s value. It is important to learn how to judge a stone for clarity.
The Gemological Institute of America (GIA) has established a rating system for
expressing the clarity of a particular stone. This rating system is based on
the use of initials and numbers and goes on a one to 10 oriented system
wherein 10 would be the best stone and one would be the worst stone.
This system is not expressed in simple numbers but with words and initials to
further establish the rating scale. The scale is as follows:

10 – Flawless – no blemishes can be found.

9 – VVS-1 – no flaws inside the table. Possible very small internal
flaws outside the table. If any external flaws are present,
must be very minor.

8 – VVS-2 – very difficult to see flaws with 1 0x magnification power
employed.

7 – VS – 1 – flaws readily seen using 1 0x glass but almost impossible
to see when the stone is viewed from from the back.

6 – VS – 2 – the back looking down through the stone.

5 – Sl – 1 – flaws unable to be seen with the naked eyes but quite
apparent using 1 0x magnification.

4 – Sl – 2 – inclusion may include carbon spots or clouds or feathers
underneath the table or larger flaws outside of the table.

3-1 – I-1 to 3 – this is the least valuable group. They are heavily flawed
and the flaws can be determined with the naked eyes. There
are going to be internal flaws inside the table, maybe
clouds, groups of carbon spots, feathers and/or cracks
that can be seen with the eye.

VVS – Very, very, slightly imperfect
VS – Very slightly imperfect
Sl – Slightly imperfect
I – Imperfect

A flawless stone is simply that. No flaw can be found even with the use of a
10x jeweler’s loupe or 10x microscope. As you go down the scale, the VVS-1 may
have one very small inclusion, generally not in the table (which I’ll cover it
later in the file) portion of the diamond but possibly on the edge. Again,
this flaw is seen only from the front and only on using 10x magnification. It
should not be visible to the naked eye.
As we get into VVS-2, there may be more than one flaw wlth magnification but
they’re still extremely small. One small inclusion may be in the table area of
the diamond.
Into the VS grades, the flaws become larger and more prominent than their VVS
cousins. VS2 may have larger flaws or a number of small spots possibly located
in the table of the diamond that group together and are almost considered one
flaw. They are generally in the same area.
When we talk about 10x magnification, this can be in the form of a jeweler’s
loupe which is a fairly inexpensive must-have item for anyone serious about
stones or a step upward which is the two eyepiece (stereo) microscope, which
many jewelers will have on the premises and will let one borrow when perusing
their stones.
It is wise to always make sure that the magnification device employed is 1Ox.
This is the standard and any variation from this will affect the rating of the
stone to a great degree.
Note that flawless VVS and VS rated stones are rated when looking at the stone
right side up with a 1 Ox magnification device. If you pick up a stone that
supposedly falls under one of these ratings and you can see inclusions with
the naked eye, you’re not looking at a stone that is properly rated.
An Sl-1 rated stone will have inclusions that are very obvious under 1Ox
magnification, but should still be borderline visible or not visible when
viewed with the naked eye. The Sl-1 stone may have these borderline visible,
small dots or inclusions in the table or edge of the stone. An Sl-2 rating
will have larger flaws and probably more than one. These will be easily
visible to the naked eye.
In the I grades, the stones can be considered either quite flawed or imperfect.
Flaws are probably inside the table. There may be flaws of more than one
variety, clouds, cracks or groups of black or white carbon spots will be
visible. This last group of stones obviously are the least valuable and the
least interesting for anyone trying to convert from cash to gems and back
again.
Looking backward we can infer several things, the first of which being if you
can spot a number of inclusions without the use of magnification device, the
stone is going to be graded 1, whether l-1, I-2 or l-3 is open to some
subjective effort, but it will be an I rated stone.
If you can’t find flaws with your eye alone but they do become visible when
using a loupe, one can assume that the stone is an Sl rated stone.
The differentiation between an S stone and a VS stone is that in a VS stone
inclusions may not be seen extremely clearly even with the loupe. If the stone
is turned over and laid on the flat front part (the face of the stone – this
is the table) and one views down from the back of the stone where all the
facets come to a point and the flaws are more readily seen here, one can
assume it is a VS-2 or above rated stone.
Note this viewing is done under white light and with the stone loose. It is
very difficult to judge any of the 4 C’s when the stone is mounted. Mounted
stones are not generally considered for investment grade purchases. The stone
should be loose and one should be able to turn it freely.